Boiler Manuals for the Heatline Compact C24 appliance. View and Download Heat Line C24 installation, servicing and user instructions manual online. condensing wall mounted combination boiler. C24 Boiler pdf. Heat line C24 Pdf User Manuals. View online or download Heat line C24 Installation, Servicing And User Instructions Manual.
|Published (Last):||16 April 2011|
|PDF File Size:||19.64 Mb|
|ePub File Size:||13.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
Re-assemble in reverse order Central heating sensor replacement 1.
Hot water demand will take heating mode whenever hot water tap is opened. Heating circuit pressure sensor fault. Re-set function Whenever boiler gets locked out, mannual should verify the gas supply and ionisation probe position. If I just do six more random replys I think I can then post a link for the instructions. With out seeing it, it’s a bit hard to be sure though.
SOLVED: Where do i find a dwh sensor on a heatline c24 – Fixya
Remove the air pressure switch by pulling forward off its bracket 6. Verify that the sensor is connected to the main board and the shunt is removed. After waiting a week for basic boiler cover insurance to come out decide to give one of the trades on site for advice. Release the main gas connection between the gas valve supply tube and gas inlet valve, retaining the washer for use on reassembly 7.
While waiting for a replacement part the insurance happened to call out and change manuao DHW sensor as this was the one flashing on the front panel and showing up as the error. Press the button to confirm. Verify the sensor F76 Thermal fuse fault Verify the fuses connections. That can be achieved by fitting dip switch number 5 into the position ON — 45 seconds delay: No, create an account now. Lately during the filling cycle water hammer is occurring.
Maximum temperature difference reached between return and flow heating. Remove the exchanger from the gap on the left hand side as shown the picture hetline 6. The water circulation is shown on the picture below.
Remove the sensing tube and electrical connections from the air pressure switch, noting which tube is connected to which port as shown on the picture below 5. Remove the pipe clips on the pipes of heat exchanger 5. Remove the clop on the pump body and then release the pipe of the expansion vessel as shown on the picture below 6.
I find it first time!!! Release the connection from gas valve and manifold inlet, retaining the washers for use on reassembly as shown on the picture below. Click “Add” to insert your video. Article num- Gas Council The identification plate keeps record of Number the country in which the product is to be Heatlinw 2 24c installed. The water circulation is shown on the picture below Central heating and domestic hot water mode When heating demand is requested, power is on and the thermostats are calling for heat, the boiler fires.
Open the isolating valves on the flow and return connections. Verify the operation of the condensate pump F83 No water in the installation: Boiler parts Each Heatline boiler is equipped with following additional parts: A professional would have the MI available to him or be able to download it from the makers web site.
Before putting the appliance into operation remember to drain the plastic discharge c4. Not to offend you but thanks for reading and your reply in the first place.
If so water maker is bad. Located on the outlet pipe- the primary heat exchnager is monitoring the water temperature coming from an overheat thermostat. To arrange parts replacement contact Heatline customer service specialists by explaining what is being requested, providing an error message if any appears on the LCD display.
The Heatline C24 and C28 boilers are compatible with a broad range of third-party roomstats and clocks. Gain General Access -remove outer case front panel 3. System pressure need to be charged to the value of around 1.
Heat Line Capriz 2 24c Operating Instructions Manual
To correctly fill in the water into the system you should follow the steps below: Verify the appliance DSN number is correct. Verify the igniter unit F28 Ignition fault Verify the return gas circuit gas valve open.
Disconnect the electrical leads and air pressure switch connection tube from the fan. F70 User interface incompatible with the main board Verify that the appliance DSN code on the screen matches the product code of the nameplate. Sensor should be removed by using 13 mm spanner 5.
Heat Line C24 Manuals
Disconnect the leads from the sensor as shown on the picture below 4. New Home Boiler Range. Naturally domestic hot water demand will draw temporary preference over the heating for the time of how water demand and 3 min cooling period. Always isolate the electricity supply Conduct all electrical check: Disconnect the leads from the sensor 6.
With out trying to confuse things, would it be right to have one 3core and earth flex from a junction box, and have the stat wired to that instead of the boiler? Verify the flow and return heating sensor connections. You must log in or sign up to reply here. Safety 1 1 Safety ral heating installations and for hot water generation.